Main Page
Peugeot 208 Key Replacement
It is best to delegate the replacement of peugeot 107 key replacement keys 208 to auto locksmiths who have the necessary equipment and technical knowledge. They will be able to create and program new keys quicker than a dealership and at a lower cost.
If your key fob stopped locking or unlocking your doors it is likely due to a dead coin battery. There are other causes for the key to be malfunctioning.
Dead Coin Battery
A dead coin battery can prevent your Peugeot car key not working 208 from locking or unlocking and will not start the engine. In this case you'll have to use the alternative starting method found in your vehicle's owner's manual.
Another reason why the 208 won't start is because the spark plugs have been damaged. The spark plugs are responsible to ignite the fuel that ignites the engine. They have a limited lifespan. They'll eventually degrade if they're not used enough.
There is a straightforward solution to this problem. Check the voltage of your battery with a multimeter. If the voltage is below 11,5 volts, it's time to replace it. If the battery is corroded, it is important to clean its contacts. This can be done by removing the rubber cover from the two terminals of the battery, and then using a wirebrush, you can remove any damaged parts of the battery. Then, reconnect the cables that connect the positive and negative poles.
Water Damage
If your 208 won't turn on and the battery is not flat, then you need to make sure whether the spark plugs are working. You might find that they're dirty and don't spark. The spark plugs can be cleaned in a workshop.
Peugeot cars have transponder keys that works with the car's ignition system. This ensures only the correct key can turn the engine. If the chip in the Peugeot key is damaged, it will not send the proper signal to the vehicle.
Water damage is a frequent reason for this issue. This is a common issue in warmer climates where the vehicle is exposed to snow or rain. If this is the case, call a reputable auto locksmith who will have all of the tools and equipment required to modify the new key. They will also have the latest technology and the machinery needed to make the peugeot 3008 key fob programming 208 smart key. The process shouldn't take longer than 15 minutes.
Contacts to the battery are not working properly.
Peugeot replaced the old transponder chips with a brand new version that makes use of electronic components that are mounted on a circuitboard. This new technology works great when it's brand new, but over time the circuit boards start to wear out and stop functioning properly.
This could prevent the immobiliser chip from working, so your car won't start. Contact an Peugeot specialist or a locksmith if this is the situation.
Another common issue is when the battery for the key fob gets depleted, which causes the key blade to stop getting into the lock. A locksmith for cars can replace the battery and cut a new blade for you, it's normally a quick fix.
Faulty Receiver Module
It could be that the receiver module has a problem If your Peugeot key fob stops working after being dropped on the floor, exposed to a sudden storm or accidentally washed. The receiver module is responsible for transmitting radio frequencies to the onboard computer that manages the central locking system of your Peugeot vehicle.
The key fob itself has rubber seals which prevent water from reaching the electronic chip inside. However prolonged exposure to water could break through these seals, causing damage to the chip. The high salt content in the ocean water or pool can cause damage to the key fob when it is submerged.
If your peugeot partner key fob programming spare key fob isn't working You'll need the module replaced. This can only be completed by an experienced auto locksmith or Peugeot specialist. Unlike other cars, Peugeot keys are protected by an unique immobilizer system that requires the correct programming to start the engine. This is the reason that you should only trust an authorized Peugeot locksmith to create and program a replacement.
Computers with faulty on-board computers
The on-board computer inside your Peugeot is the one responsible for all of the systems within your vehicle, from airbags to power windows. The on-board computer will show a code if something goes wrong. This code will be saved in the system until the problem is fixed. This may require the on-board computers to be replaced.
The most frequent cause for the warning light of the airbag to come on is corroded or loose connections within the sensor. This can be caused by wear and tear, aging, or exposure to moisture and salt. This issue needs to be dealt with as soon as you can, because an airbag malfunctioning could pose a risk in the event of an accident.
If your Peugeot is showing a card not detected error, then the key battery inside the key fob could be dead or weak. This prevents the key fob from sending a signal to disable the immobilizer on your vehicle's standard. Test this by pressing the unlock button on the key fob and then trying to start your car. If this doesn't work, then the key battery will need replacing.